There are three types of installations for the Magfinity series:
1) Surface Mounted
Below are the different options easily described, step by step, for a smooth and correct installation.
Manuals are designed for basic mounting installations. Choose the mounting option according to the ceiling type. For custom installation that requires special assistance, please contact our team for detailed information.
Taking the MAGfinity track and terminal box dimensions into consideration, measure and draw your desirable track line on the drywall surface.
Find the ideal placement for remote LED drivers either at the nearest utility room or the track power box. From there, run the wires to approximate terminal box location.
Take a precise measurement at the MAGfinity track for straight and leveled clips positioning. Attach mounting clips to your surface with a screw.
Connect power wires to the terminal box. Take internal power plates out of the MAGfinity track and place it into the opening. Make sure your track is straight and level. Screw the fixture through right into a bracket, one by one.
Place the MAGfinity track securely against the mounting clips, make sure the clips sit in the track. Firmly rotate to fasten each clip.
If needed, connect all the MAGfinity track's consecutive elements with a pin in between the power plates located on each component.
After successful pin connection, secure two MAGfinity elements by coupler
Find the ideal placement for remote LED drivers. Either at the nearest utility room or the track power box. From there, run the 16-18 gauge wires to your J-Box location.
Measure the desired height from the fixture to the ceiling. The power feed cable is 16 ft long, the fixture can be placed within that distance.
Make sure to save 6 inches for electrical connection at the j-box. And save 6 inches for electrical connection at the terminal box.
Cut and discard excessive cable length.
Unscrew the grippers from the hangar mounts.
Slide the hangar mounts onto the top side of the track.
The aircraft cable’s length can be adjusted through the gripper.
Cut and discard excessive cable length.
Complete step by screwing the gripper back to the hangar mounts
Take the terminal box out and remove the cover by sliding out. Using a screwdriver, remove the pre-installed wires from the terminal box. Make sure to keep the internal wires untouched.
Insert power feed cable from the canopy set to the terminal box and fasten them with a screwdriver.
- Black is negative (Black to Black)
- White is positive (White to Red)
Insert the pin into the slots on the power plate and terminal box.
Using the coupler, attach and fasten the terminal box to the MAGfinity track.
Pull the feeding cable through the cable bushing on the canopy plate.
Connect the feeding cable wires from the inside of the canopy to the preinstalled electrical wires inside the J-box using WAGO connectors.
Using the screws on the side, Insert the canopy cover plate over the mounting bracket. Securely place it on the j-box.
If needed, connect all the magtrack's consecutive elements with a pin in between the power plates located on each component. Please make sure to slide the hangar mounts onto the top side of another MAGfinity track before connection.
Taking the MAGfinity track dimensions into consideration, measure and draw your desirable track line on the drywall surface.
Cut into drywall to create opening. Make sure the cut is precise and does not exceed 1/8" of a fixture size for a sharp looking installation.
Find the ideal placement for remote LED drivers either at the nearest utility room or the track power box. From there, run the wires to either end of your opening.
Using WAGO connectors, attach 3 pin connectors to your power supply wires. Each power supply requires 110/277 VAC connection.
Join the flexible 2 pin connectors first and place the track into the drywall opening.
Note: For single fixture run, attach the end cap to both ends.
Secure the track with the screws through the trim holes around. Make sure the track is secured.
If needed, connect all consecutive elements of the track with the 2 pin connectors located on each component. Secure into place by following step 6 with the newly consecutive tracks.
For multiple fixture runs, attach the end caps to the beginning and the end of your run.
Secure the newly connected track with screws through the trip holes around. Make sure the track is secured.
Continue Step 7 and 8 for any continuing tracks.
Using painter's tape, cover the track slot. Add plaster on the track trim and smoothly patch it with a compound knife. Even the patched drywall surface out. Let it dry 12 hours minimum.
Sand, the patched area, make sure to sand along the taped edge area for a smooth transition.